Bites Clean. Sits Flush. Never Strips Out.
Stop ruining fine woodwork with soft hardware-store screws that wobble on your bit and snap off mid-turn.
Claim 50% Off — Order NowIn Stock – Free 5–7 Day US Shipping
Every detail of the Cosari MicroGrip M2 assortment is built to eliminate the frustrations of cheap big-box blister packs and messy uncalibrated import kits.
Includes 100 pieces each of M2×4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, and 20mm—so you never poke a screw through a thin lid or come up short on cabinet trim.
Precision-forged cross recesses seat your #0 or #1 driver tip squarely on the first try, delivering clean hand torque without rounding out or scarring brass hardware.
Needle-sharp tips and high-crest spiral wood threads bite immediately into softwood without pilot holes and pull hardware tight without turning into 'spinners.'
Engineered with a true 90-degree flat-head taper that seats completely flush inside miniature butt hinges, clasps, and trim plates so lids close without binding.
Instead of blunt machine threads that chew up delicate grain, each M2 screw features a razor-sharp 28° point and coarse wood-biting flutes that pull straight down on the first turn.
Hardened carbon steel with a bright nickel-silver finish prevents the Phillips cross-slot from deforming, keeping your #0 or #1 precision screwdriver locked straight from start to finish.
The 90° countersunk head tucks cleanly into small hinge leaves and wood countersinks, leaving a gleaming, snag-free silver finish that resists shop humidity and rust.
Limited-Time Direct Offer — Save 50% Today
800 Precision Hardened M2 Flat-Head Wood Screws (4mm–20mm) in a Dual-Latch 10-Grid Bench Organizer
Backed by our 30-Day Money-Back Trial & Full Cosari Guarantee.
$29.99 $59.99 Free Tracked Shipping (5–7 Days) Included
In Stock: Delivers in 5–7 Business Days. Free insured US delivery with tracking.
30-Day Money-Back Guarantee plus a full 2-Year Warranty.
Quantity
What's Included & Exact Size Breakdown: Inside the 10-compartment translucent snap-latch organizer box (132mm × 68mm × 23mm), you receive 800 M2 (2.0mm diameter) flat-head Phillips wood screws: 100× M2×4mm, 100× M2×5mm, 100× M2×6mm, 100× M2×8mm, 100× M2×10mm, 100× M2×12mm, 100× M2×16mm, and 100× M2×20mm. Two additional empty compartments inside the 10-grid case let you store miniature hinges, catches, or driver bits.
Material & Metallurgy Specifications: Forged from hardened carbon steel and electroplated with a bright, corrosion-resistant nickel-silver finish. Features a 90-degree countersunk flat head (3.8mm head diameter), deep centered #0/#1 Phillips drive recess, coarse wood-gripping thread pitch, and a 28-degree self-tapping point.
Recommended Workshop Applications: Ideal for mounting jewelry box hinges and clasps, miniature cabinet trim, guitar and luthier pickguards/tuners, scale wooden ship and RC models, humidor restoration, eyeglass/watch case repair, and 3D-printed or wooden electronics enclosures.
Free 5–7 Day US Shipping: Every order ships free with full tracking and delivers in 5 to 7 business days.
30-Day Trial: Try it at home for 30 days risk-free. Need help? Email us anytime at support@buycosari.com.
2-Year Warranty: If anything goes wrong within 2 years, we replace it free of charge or refund your order in full.
Big-box mini packs use soft zinc castings that twist apart in oak. Cosari heat-treats carbon steel and finishes it in bright nickel so slots stay crisp and shanks stay strong.
Full-height baffle dividers meet the inside of the closed lid while dual front snap-latches lock tight—so your 4mm and 20mm screws never mix together in a tool drawer.
Buying 100 retail 8-packs at $2.48 each costs $248.00. Get all 800 calibrated M2 screws in a reusable workshop case for just $29.99 today.
Cosari MicroGrip 800-Piece M2 Flat-Head Wood Screw Assortment KitStandard Competitors
| Feature | Cosari MicroGrip 800-Piece M2 Flat-Head Wood Screw Assortment Kit | Standard Competitors |
|---|---|---|
| Cost for 800 Micro Wood Screws | $29.99 Total (3.7¢ per screw) | $248.00 in $2.48 retail 8-packs (31¢ per screw) |
| Phillips Cross-Slot Precision | Deep, centered #0/#1 recess — zero bit wobble | Shallow, off-center stamping that cams out |
| Shank & Thread Metallurgy | Hardened nickel-plated carbon steel with 28° point | Soft zinc alloy with blunt tips & shallow threads |
| Metric Micro Size Range | 8 exact M2 lengths: 4, 5, 6, 8, 10, 12, 16 & 20mm | Limited imperial gauges that split thin wood |
| Storage & Drawer Organization | 10-grid translucent box with dual front snap-latches | Loose plastic baggies or flimsy wheels that spill |
Swipe left for steps 2 and 3
Pop open the dual front snap-latches on the 10-compartment translucent case and select the exact length (4mm to 20mm) required for your wood thickness.
Press your #0 or #1 Phillips precision tip into the deep cross-slot—where the screw holds straight without wobbling—and align the sharp self-tapping point with your mounting hole.
Turn smoothly by hand as the coarse threads pull the screw downward until the 90° flat head sits dead-flush with your hinge leaf or wood surface.
I used these on a little outdoor craft project with a low-clutch driver. They went in smoothly without wobbling or stripping, and the shiny silver heads sit clean and flush in the wood. No rust spots after a few months of rain and sun.
The sharp points bit right into my basswood pieces without a pilot hole. I used a #0 Phillips precision bit, and the threads pulled the screws in quickly without stripping the heads.
I used this assortment to attach hinges on a couple of jewelry boxes. The silver finish looks clean, and the Phillips slots held my screwdriver without slipping. Plenty of different lengths left for other small repairs.
Fixed the loose pieces on my daughter's miniature dollhouse furniture with these. The cleanly cut Phillips flat heads were easy to work with, and the screws went into the little wood pieces nicely.
Perfect. These feel strong and the quality has been flawless for my small woodworking jobs. Getting 800 assorted screws in a box costs less than stocking up on those tiny individual bags at Lowe's or Home Depot.
Really nice little screws. The threads are sharp, the silver finish looks clean, and the labeled 10-grid case makes it easy to find what I need at my workbench.
Worth every penny to have the lengths from M2x4 through M2x20 sorted in one snap-lid box. I use them for little wood crafts and don't have to dig through bags every time I need a shorter screw.
I like having all eight sizes around for small hinges and trim work. The heads have held up well with my precision driver. Good luck breaking or stripping one if you use the right bit.
I used to buy small boxes of each length for my woodworking bench. This translucent case has 100 each of M2x4, 5, 6, 8, 10, 12, 16, and 20, with partitions to keep them organized.
I got tired of tiny big-box screws wobbling on the bit or snapping heads in hardwood. These have deeper Phillips slots and sturdy little shanks. I've had a much easier time with them on my cabinet projects.
$29.99 $59.99 Free Tracked Shipping (5–7 Days) Included
In Stock – Free 5–7 Day US Shipping · 30-Day Risk-Free Trial.
You receive exactly 800 M2 (2.0mm thread diameter) flat-head Phillips wood screws divided evenly across 8 metric lengths: 100× M2×4mm, 100× M2×5mm, 100× M2×6mm, 100× M2×8mm, 100× M2×10mm, 100× M2×12mm, 100× M2×16mm, and 100× M2×20mm.
Yes. Following international DIN/ISO standards for 90-degree countersunk flat-head wood screws, the stated length (4mm through 20mm) represents the total overall length from the top flush surface of the head to the self-tapping tip.
A #0 or #1 precision Phillips screwdriver fits the cross-recess tightly with zero wobble. Avoid using a large #2 drywall bit or a high-torque cordless impact driver.
No. The 10-compartment translucent polypropylene case is molded with full-height divider walls that meet the closed lid, secured by dual front snap-latches so each length stays in its dedicated bay.
In softwoods such as pine, basswood, balsa, fir, and cedar, the 28-degree needle-sharp self-tapping point bites immediately without a pilot hole. When driving into dense hardwoods like oak, maple, or walnut—especially with the longer 16mm and 20mm lengths—we recommend pre-drilling a 1.5mm (1/16 inch) pilot hole.
Put the Cosari MicroGrip kit on your workbench for 30 days and test the screws on your own projects. If you aren't thrilled with how cleanly they drive, how flush they sit, or how well the case stays organized, simply contact us for a full 100% refund.